LG M4214CCWA Uživatelský manuál

www.lg.comOWNER’S MANUALMONITOR SIGNAGEMONITOR SIGNAGE MODELSM4214CPlease read this manual carefully before operatingyour set and retain it for future

10First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable.When connecting with the D-Sub s

11Select an input signal.Press the INPUT button on the remote control to select the input signal. Or, press INPUT on the bottom of the set.• How to c

12• Using LAN establishes communication between your PC and the monitor and enables to use the OSD menus on the PC as well as on the monito

13Connecting to External DevicesDaisy Chain Monitors When using RGB input When using AV input To use different products connected to each other Conne

14Kensington Security Slot The Set is equipped with a kensington Security System connector on the back panel. The cable and lock are available separat

15NoteConnecting to External DevicesCable Management- Only on some models.Cable Management Hold the Cable management with both hands and pull it downw

16Connecting to External DevicesWhen connecting with an BNC cable.• Select AV. Connect the video cable as shown in the below figure and then connect

17• Select Component.Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page 10).• Connect the input ter

18Connect the video/audio cable as shown in the below figure and then connect the power cord (See page 10).RCA-PC Audio Cable(not included)ProductVCR/

19User MenusScreen Adjustment optionsPress this button to turn on the power. Press this button again to turn it off.This Indicator lights up green whe

2Table of ContentsAccessories 3Connecting the stand 4Connecting the Speakers 5To install Portrait 6Using the Remote Control 7Name and Function of

20User MenusThis is where the unit receives signals from the remote control.Screen Adjustment options[For PC Analog signal]AUTO/SET Button AV Composi

21OSD Menu NoteOSD(On Screen Disp lay)• The OSD function enables you to adjust the screen status conveniently since it provides graphical

22User MenusHow to adjust the OSD (On Screen Display) screen• Use the remote control to adjust the OSD screen.How to adjust the screen automaticallyPr

23User MenusAdjusting Screen ColorAspect RatioMoveOKPICTUREAspect Ratio : 16:9 Energy Saving : OffPicture Mode : Standard • Backlight 70 •

24MoveOKPICTUREAspect Ratio : 16:9ꕫ Energy Saving : OffPicture Mode : Standard • Backlight 70 • Contrast 90 • Brightness 50 • Sharpn

25Adjusting Screen ColorUser MenusPicture ModeMoveOKPICTUREAspect Ratio : 16:9 Energy Saving : OffPicture Mode : Standard • Backlight 70 •

26User MenusMoveOKPICTUREAspect Ratio : 16:9 Energy Saving : OffPicture Mode : Standard (User) • Backlight 70 • Contrast 90 • Brightn

27User MenusMoveOKPICTURE ▲ • Contrast 90 • Brightness 50 • Sharpness 70 • Color 60 • Tint 0 • Advanced Control • Picture ResetS

28User MenusMoveOKPICTURE ▲ • Contrast 90 • Brightness 50 • Sharpness 70 • Color 60 • Tint 0 • Advanced Control • Picture ResetS

29Adjusting the audio functionUser MenusMoveAUDIOAuto Volume : OffClear Voice II : Off • Level 3Balance 0Sound Mode : Standard • Treble

3NC2000 kit❖ Applicable only for models that support the NC2000.Without prior notice, optional accessories are subject to change to improve the perfor

30Adjusting the timer functionUser MenusMoveTIMEOKClockOff Time : OffOn Time : OffSleep Timer : OffAuto Off : OnPower On Delay : OffClock

31User MenusMoveOPTIONOKLanguage : EnglishInput Label Key Lock : OffSet ID : OffISM Method : NormalDPM Select : OnPower Indicator : O

32User MenusDPM SelectA user can choose to turn the power saving mode on / off.Power IndicatorUse this function to set the power indicator on the fron

33Tile mode and choose Tile alignment and set the ID of the current product to set location.Only after pressing the SET button the adjustments made to

34- Tile mode (product 1 ~ 2) : c(2) x r(1)- Tile mode (product 1 ~ 9) : c(3) x r(3)- Tile mode (product 1 ~16) : c(4) x r(4)rowcolumnID 1ID 5ID 9ID 1

35User MenusAdjusts the USB options.When connecting the USB deviceWhen you connect a USB device, this pop up menu is displayed, automatically.“POP UP

36User MenusAdjusts the USB options. Precautions when using the USB device• Only a USB storage device is recognizable.• If the USB storage device

37User MenusAdjusts the USB options.You can view photo files on USB storage device.The On Screen Display may be different from your TV. Images are an

38Photo ListPage 2/3Drive1JMJ0011366x768, 125KBUp FolderUp FolderKY101 02/12/2010KY102 02/12/2010JMJ001 02/12/201

39User MenusAdjusts the USB options.◄ 1/17 ►Slideshow ◘ BGM ◘ Delete Option Hide꘤ ► Slideshow When no picture is selected, all pho

4Connecting the stand- Only on some models.2.3.1.Take the parts for the stand out of the box and assemble them as shown in the picture. Place a soft

40User MenusYou can play music files on USB storage device.Purchased music files(*.MP3) may contain copyright restrictions. Playback of these files ma

41Music Selection and PopUp Menu➩As shown, up to 6 music titles are listed per page.User MenusAdjusts the USB options.Music ListPage 2/3MusicS00300:00

42MusicS0030:27 / 3:67 If you don't press any button for a while during the playing, the play information box (as shown in the below) will floa

43The movie list is activated once USB is detected. It is used when playing movie files on TV.Displays the movies in the USB folder and supports Play.

44User MenusAdjusts the USB options.Page 2/3MovieM002640x480, 720KBUp FolderTitle DurationUp FolderFavorite MusicM001M002M001M00101:34:1501:35:3001:30

45Movie Selection and PopUp Menu➩User MenusAdjusts the USB options.Page 2/3MovieM002640x480, 720KBUp FolderTitle DurationUp FolderFavorite MusicM001M0

46Using the remote controlUser MenusAdjusts the USB options.◄◄ / ►►When playing, repeatedly, press REW (◄◄) to speed up ◄◄(x2) -> ◄◄◄ (x4) -> ◄◄

47User MenusMoveUSBOKPhoto ListMusic ListMovie ListDivX Reg. CodeDeactivationDivX Reg. Code ꔋAdjusts

48MoveUSBOKPhoto ListMusic ListMovie ListDivX Reg. CodeDeactivationDeactivation ꔋDeactivation T

49Troubleshooting• The control locking function prevents unintentional OSD setting change due to careless usage. To unlock the controls, simultaneous

5Connecting the SpeakersMount the product onto the speaker by using a screw as shown in the following connect the speaker cable.When the speaker is in

50Troubleshooting● Is the screen position wrong?● Do thin lines appear on the background screen?● Horizontal noise appears or the characters

51Troubleshooting• Set the number of colors to more than 24 bits (true color) Select Control Panel - Display - Settings - Color Table menu in Wind

52Specications Note• The specifications shown above may be changed without prior notice for quality improvement.LCD PanelPower Dimension

53 Specications Note• The specifications shown above may be changed without prior notice for quality improvement.Max. Resolution RG

54 Specications PC Mode - Preset ModeNote• DTV/PC selection on HDMI/DVI inputs is available for PC resolutions : 640 x 480/60 Hz, 1280 x 720/60 Hz,

Controlling the Multiple ProductRS-232CA1Controlling the Multiple ProductRS-232CA1A1Connecting the cableConnect the RS-232C cable as shown in the pict

Controlling the Multiple ProductRS-232CA2 COMMAND 1 COMMAND 2 DATA1

Controlling the Multiple ProductRS-232CA3 COMMAND 1 COMMAND 2 DATA1

Controlling the Multiple ProductRS-232CA4OK Acknowledgement * The Product transmits ACK (acknowledgement) based on this format when receiving normal

Controlling the Multiple ProductRS-232CA5Transmission / Receiving Protocol01. Power(Command : a)► To control Power On / Off of the Set.TransmissionDat

6To install Portrait"When installing Portrait, rotate it clockwise based on its front."- Only on some models.

Controlling the Multiple ProductRS-232CA603. Aspect Ratio(Command : c) (Main picture format)► To adjust the screen format. You can also adjust the

Controlling the Multiple ProductRS-232CA7A705. Volume Mute(Command : e) ► To control On/Off of the Volume Mute.TransmissionData 0 : Volume Mute On (V

Controlling the Multiple ProductRS-232CA8A8Transmission / Receiving Protocol07. Contrast(Command : g)► To adjust screen contrast. You can also adj

Controlling the Multiple ProductRS-232CA9Transmission / Receiving Protocol09. Color(Command : i) (Video Timing only)► To adjust the screen color. Y

Controlling the Multiple ProductRS-232CA1011. Sharpness(Command : k) (Video Timing only)► To adjust the screen Sharpness. You can also adjust the

Controlling the Multiple ProductRS-232CA11Transmission / Receiving Protocol14 Balance(Command : t)► To adjust the sound balance.TransmissionData Min

Controlling the Multiple ProductRS-232CA12Transmission / Receiving Protocol16. Abnormal state (Command : z)► Abnormal State : Used to Read the power o

Controlling the Multiple ProductRS-232CA1318. Auto Configure(Command: j u)► To adjust picture position and minimize image shaking automatically. it

Controlling the Multiple ProductRS-232CA1420. Tile Mode(Command : d d)► Change a Tile Mode.Transmission* The data can not be set to 0X or X0 except 00

Controlling the Multiple ProductRS-232CA1521. Tile H Position(Command : d e)► To set the Horizontal position. TransmissionData Min : 00H to Max : 14H

7Using the Remote ControlName of the Remote Control Buttons12534769813121110Power On / Off Button- Switches the set on from standby or off to

Controlling the Multiple ProductRS-232CA1623. Tile H Size(Command : d g)► To set the Horizontal size. TransmissionData Min : 00H to Max : 64H* Refer

Controlling the Multiple ProductRS-232CA17A1725. Tile ID Set(Command : d i)► To assign the Tile ID for Tiling function . TransmissionData Min : 00H t

Controlling the Multiple ProductRS-232CA18A18Transmission / Receiving Protocol28. Sound Mode (Command : d y )► To adjust the Sound mode. Transmission

Controlling the Multiple ProductRS-232CA19Controlling the Multiple ProductRS-232CA1931. Temperature value (Command : d n) ► To read the inside tempera

Controlling the Multiple ProductRS-232CA20Controlling the Multiple ProductRS-232CA2033. Auto volume (Command : d u) ► Automatically adjust the volume

Controlling the Multiple ProductRS-232CA2135. Time (Command : f a) ► Set the current time. Transmission[Data1]0 : Monday1 : Tuesday2 : Wednesday3 : T

Controlling the Multiple ProductRS-232CA22Transmission / Receiving ProtocolTransmission [Data1]1. f1h to f4h(read one index) f1: read 1st

Controlling the Multiple ProductRS-232CA23Transmission[Data 1]1. f1h to f4h(read one index) f1: read 1st index of Off Time List,

Controlling the Multiple ProductRS-232CA24Transmission / Receiving Protocol38. Scheduling Input select (Command : f u) (Main Picture Input)► To select

Controlling the Multiple ProductRS-232CA2539. Sleep Time (Command : f f) ► Set Sleep Time. Transmission Data 0 : Off1 : 102 : 203 : 304 : 605

8Energy Saving Button- Adjust the Energy Saving mode of the SET.INPUT Select ButtonIf you press the button once, the following Input Signal W

Controlling the Multiple ProductRS-232CA2641. Power On Delay (Command : f h) ► Set the schedule delay when the power is turned on (Unit: se

Controlling the Multiple ProductRS-232CA2743. DPM Select (Command : f j) ► Set the DPM (Display Power Management) function. TransmissionData 0 : Off

Controlling the Multiple ProductRS-232CA2845. Power saving(Command : f I) ► To set the Power saving mode. Transmission Data 0 : Off 1:

Controlling the Multiple ProductRS-232CA29Transmission / Receiving Protocol47. logo Indicator (Command : f p) ► To set the LED for Power IndicatorTran

Controlling the Multiple ProductRS-232CA3049. S/W Version (Command : f z) ► Check the software version. Transmission Data FFH : ReadAcknowledg

Controlling the Multiple ProductRS-232CA31IR CodesRS-232CA31 Remote Control IR Code Output waveform single pulse, modulated with 37.917kHz s

Controlling the Multiple ProductRS-232CA32IR CodesRS-232CA32Code(Hex) Function Note UP

Controlling the Multiple ProductRS-232CA33IR CodesRS-232CA33E0E12899727163617BB0B1BA8F8E5ABFD5C67677AFR/C ButtonR/C ButtonR/C ButtonR/C Button(Discret

Ma ke su re to re ad t he Im p or t an t Precautions before using the product.Keep the Owner's Manual(CD) in an accessible place f

9Name and Function of the PartsRear View* LINE OUT A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that t