LG LRN8240D-NH Uživatelský manuál stáhnout pdf (Strana 31)

Installation

• Audio/Sensor setting

You can configure this option when you select to [LGE] on the

[Driver] option. Select [Audio/Sensor] tab of the [Setup] window.

- Audio In: Click the check box if you want to send the audio

from the microphone input connector.

- Audio Type: Select the codec when you send the audio from

the microphone input connector.

- Audio Out: Click the check box to output the audio from the

speaker.

- Sensor: Select the sensor number on the drop-down list.

- In Use: Marks up when you want to activate the sensor.

- Sensor Type: Select the sensor type.

- Relay Output: Select the relay output number

on the drop-down list.

- Relay Type: Select the relay type.

- Control Duration: Enter the relay time.

Motion Setting

You can configure this option when you select to [LGE] on the

[Driver] option. Select [Motion] tab of the [Setup] window.

1. Click the [Add] button. The motion detect window is

displayed. You can add the five windows maximum for

motion detection area.

2. Set the [Sensitivity] option.

3. Click the edge or corner of the window box to adjust the

window size for motion detection.

4. Click the [Save] button to save the settings.

Stream Setting

If you select to [LGE] on the [Driver] option, select the [Stream]

tab. When you select [ONVIF] on the [Driver] option, you can

configure the stream setting only. In case of [AXIS], the [Bitrate]

and the [Compression] options are activated only.

- Stream (LGE only): Select the video stream.

- In Use (LGE only): Click to activate the stream function.

- Video Codec: Select the video mode (Codec) from the

dropdown list.

- Resolution: Select the output image size of the camera.

- Frame Rate: Set the frame rate of the image.

- GOP: It means “Group of Pictures”. The higher the GOP, the

better is the video quality of the camera. Edit the value of

GOP from 1 to 30. This setting is valid for H.264 video format

only.

NOTE

It recommended that you set the [GOP] value same as

[Frame Rate].

- GOV (ONVIF only): It means “Group of VOPs”. The VOP is an

image frame in the MPEG-4 video stream. Edit the value of

GOV from 1 to 30.

- Quality: Select the Quality.

- Stream Quality (LGE only): If the [Quality] option set to VBR,

this option is displayed. Select the stream quality from the

drop down box, the camera supports five types. (Highest,

High, Medium, Low and Lowest)

- Bitrate: If the [Quality] option set to CBR, this option is

displayed. Edit the bit rate value from 256 kbps to 10 240

kbps.

- Compession (AXIS only): Enter the compression ratio of

video. The lower value you set up, the higher definition

picture you get.

• Delete: Click the check box of the desired channel and then

press the [Delete] button. Registered channel of IP Camera will

be deleted.

To register the IP device automatically

1. Click the [AUTO] button.

2. The search window will be displayed and start to search the IP

device automatically. By stopping or restarting the search, click

[Stop] or [Refresh] button.

3. Click the check box of desired device.

4. Enter the [User Name] and the [Password] and then click the

[Add] button. When you select several channels, channels are

assigned same ID and password.

5. Confirm the result of authentication on the [Verify] option.

• O: The verification is valid.

• X: The verification is invalid. Check the ID and password

again.

• XX: Connection failed.

6. Click the check box of confirmed cameras. Selected cameras are

registered channel in order.

7. Click the [CLOSE] button to exit the window.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 58 59

Komentáře k této Příručce

Žádné komentáře

LG LRN8240D-NH Uživatelský manuál Strana 31

Komentáře k této Příručce

Související produkty a manuály pro Digitální videorekordéry (DVR) LG LRN8240D-NH