LG M1921A-BT Uživatelský manuál

Make sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for furture reference.See the

9Name and Function of the PartsRemote Control - Using the Teletext functionUPDATEPress the button to appear the TV programme. At the top of screen ind

10Name and Function of the PartsName of the Remote Control Buttons (Btype)POWERTVINPUTPRPROKMUTELISTMENUQ.VIEWSLEEPARC/UPDATESIZEHOLDINDEXSSMPSMTEXTTI

11Name and Function of the PartsPOWERTVINPUTPRPROKMUTELISTMENUQ.VIEWSLEEPARC/UPDATESIZEHOLDINDEXSSMPSMTEXTTIMEMIXREVEALMODEVOLVOLMX?iI/II*Name of the

12Name and Function of the PartsMENUUse this button to enter the On Screen Display menu.SLEEP : SLEEP TimerYou can set a time period after which the T

13Name and Function of the PartsHOLDPress the button to stop the automatically rotatingof the sub pages. Press the button again tocontinue the automat

14Name and Function of the PartsREVEALPress the button to reveal/conceal the hiddeninformation, such as solutions to riddles andpuzzles. Press this bu

15Name and Function of the PartsRear ViewPower Connector : Connect the power cord.SCART Input/Output TerminalAV Input TerminalD-Sub Analog Signal Conn

16AV Input TerminalS-Video Input TerminalAudio Input TerminalVideo Input TerminalName and Function of the Parts(RGB) INS-VIDEOAV IN 2(Mono)VIDEOAUDIOL

1717Connecting to External DevicesAUDIO(RGB) INConnecting to your PCFirst of all, see if the computer, product and the peripherals are turned off. The

18• Directly connect to a grounded power outlet on the wall or a power bar with a ground wire.NoteTurn on the PC. 21Rear side of the product.Connect t

1Safety PrecautionsPlease read these safety precautions carefully before using the product.If you ignore the caution message, you may be slightly inju

19Connecting to External DevicesWhen using the RCA cable.• Connect the input terminal with aproper colour match.When using the S-Video cable.• Connect

20Select an input signal.Press the INPUT button on the remote control to select the input signal. Or, press the INPUT button at the topside of the pro

21Connecting to External DevicesConnect the D-sub cable, RCA/PC cable as shown in the below figure and then connect the power cord. (see page 18)Conne

22Rear Side of the ProductAntenna Cable(Not included.)Check if the antenna cable is connected at the rear side of the productand then, connect the pow

23To arrange cables using cable managementcablemanagement 1.2.Arrange the cables in the center as shown in the following picture.Fit the cable managem

24Name of the Buttons in the Screen Adjustment UnitPower Indicator• Adjust the volume.• Use this button to control the channel for the TV signal.• Us

25Adjusting the ScreenName of the Buttons in the Screen Adjustment UnitOK ButtonINPUT Button• The unit that receives the signal from the remote contro

26OSD(On Screen Display)The OSD function enables you to adjust the screen status conveniently since it providesgraphical presentation. NoteOSD (On Scr

27Adjusting the ScreenOSD (On Screen Display) Screen Tracking OrderPress the MENU Button, then the main menu of the OSD will appear.To access a contro

28Adjusting the Screen1. Press the button and then, OK button to select your desired language.2. Press the button and then

22Electrical Power Related PrecautionsMake sure to connect the power cable to the grounded current.- You may be electrocuted or injured.Use the rated

29STATION ID set/Select the channel when using the TV Adjusting the ScreenIt should be set before run auto searching.Press the buttons to sel

30Press the buttons to select VHF/UHF for aerial channels or Cable forcable channels. To select the channel reception type. : VHF/UHF / Cable

31STATION ID set/Select the channel when using the TV FavouriteprogrammeThis function lets you select your favourite programmes directly. (8 channel)P

32Adjusting the ScreenPICTURE ID adjust the picture function (RGB-PC)PSMThe PSM function automatically adjusts the screenimage quality. (It is not wor

33PSMCSMThe PSM function automatically adjusts the screenimage quality. • DynamicSelect this option to display with a sharp image. • StandardThe most

34Adjusting the ScreenSSMAVLBalanceSOUND ID to adjust the sound functionThe best sound tone quality will be selected automatically depending on the vi

35TIME ID to adjust the time function • In the event of power interruption (disconnection or power failure), the Clock must be reset.• Two hours after

36Use the buttons to select On or Off. It can be set up so that it can only be used withthe remote control. This feature can prevent unauthor

37SCREEN ID to adjust the screen function Adjusting the ScreenAuto config.Manualconfig.ResetThis button is for the automatic adjustment of the screen

38Troubleshooting• Install the product driver, which is provided withthe product, or download it from the web site.(http://www.lge.com) • See if the

3Safety PrecautionsCautionPrecautions in Using the ProductWarningDo not put or store inflammable substances near the product.- There is a danger of ex

39• If you use a fixed image for a long time, the pixelsmay be damaged quickly. Use the screen saverfunction.● After-image appears when theproduct is

40• Set the colour resolution to more than 24 bits (truecolour)Select Control Panel – Display – Settings – Colour Table menu in Windows.• Check the co

41SpecificationsThe product specifications can change without prior notice for product improvement.[17 inch]Screen Type 17 inches (43.27 cm) TFT (Thin

42SpecificationsThe product specifications can change without prior notice for product improvement.[19 inch]Screen Type 19 inches (48.19 cm) TFT (Thin

43PC Mode – Preset ModePreset modeHorizontalFrequency(kHz)VerticalFrequency(Hz)Preset modeHorizontalFrequency(kHz)VerticalFrequency(Hz)1234567640 x 35

44SpecificationsVESA wall mountingConnected to anotherobject (stand type and wall-mounted type).This product accepts aVESA-compliant mountinginterface

4Before Connecting to the PCConnecting the standBefore setting up the product, ensure that the power supply, the computer system,and other attached de

5Before setting up the product, ensure that the power supply, the computer system,and other attached devices is turned off. Positioning your display1.

6Name and Function of the PartsName of the Remote Control Buttons (Atype)PROKPOWERMUTETVINPUTLIST MENUQ.VIEWPRVOLVOLI/IIMUTE POWERTV : TV buttonINPUTI

7Name and Function of the PartsPR ( ) ButtonsAble to change channel.VOL ( ) Buttons Able to adjust sound.OK ButtonUse when functiona

8Name and Function of the PartsRemote Control - Using the Teletext functionPlease select your local teletext language. (page A28)If you don't, th