LG OLED65B6Y Uživatelský manuál

P/No: MFL69387464 (1603-REV00)Printed in KoreaOLED TVOLED55B6*OLED65B6*www.lg.com X 4(M4 X L12)AA

2Safety instructionsPlease read these safety precautions carefully before using the product. WARNINGDo not place the TV and/or remote control in the f

3Do not plug too many electrical devices into a single multiple electrical outlet. Otherwise, this may result in re due to over-heating.Do not drop t

4Never touch this product or antenna during a thunder or lighting storm. You may be electrocuted.Never touch the wall outlet when there is leakage of

5 CAUTIONInstall the product where no radio wave occurs.There should be enough distance between an outside antenna and power lines to keep the former

6Signal from Remote Control can be interrupted due to external/internal lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting or

7Avoid touching the screen or holding your nger(s) against it for long periods of time. Doing so may produce some temporary or permanent distortion/d

8You may nd dierent brightness and color of the panel depending on your viewing position(left/right/top/down). This phenomenon occurs due to the ch

9•  For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that suppo

10•  When transporting a large TV, there should be at least 2 people. •  When transporting the TV by hand, hold the TV as shown in the following illus

11Mounting on a table1 Lift and tilt the TV into its upright position on a table. •  Leave a 10 cm (minimum) space from the wall for proper ventilat

1210 cm10 cm10 cm10 cmMake sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are desc

13 NOTE•  The external device connection may dier from the model.•  Connect external devices to the TV regardless of the order of the TV port.•  If y

14Slim remote control(Depending on model)The descriptions in this manual are based on the buttons on the remote control. Please read this manual caref

15Magic remote functions(Depending on model)When the message “Magic remote battery is low. Change the battery.” is displayed, replace the battery.To r

16D Used for viewing 3D video. (Only 3D models) Turns the twin mode on or o. (Depending on model) (INPUT) Changes the input source.* Pressing and ho

17TroubleshootingCannot control the TV with the remote control.•  Check the remote control sensor on the product and try again.•  Check if there is an

18CI Module1 (W x H x D) 100.0 mm x 55.0 mm x 5.0 mmEnvironment conditionOperating Temperature0 °C to 40 °COperating HumidityLess than 80 %Storage Tem

19RegulatoryWARNING! Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many i

MODELSERIALRecord the model number and serial number of the TV.Refer to the label on the back cover and quote this information to your dealer when req

OWNER’S MANUALEXTERNAL CONTROLDEVICE SETUPPlease read this manual carefully before operating the set and retain it for future reference.www.lg.com

24 51 3

2ENGENGLISH2KEY CODESKEY CODES• This feature is not available for all models.Code (Hexa)Function NoteCode (Hexa)Function Note00 CH +, PR + R/C Button

3ENGENGLISH3EXTERNAL CONTROL DEVICE SETUPEXTERNAL CONTROL DEVICE SETUP• Image shown may differ from your TV.Connect the USB to Serial converter/RS-23

4ENGENGLISH4EXTERNAL CONTROL DEVICE SETUPPhone jack Type• You need to purchase the phone-jack to RS-232 cable required for the connection between the

5ENGENGLISH5EXTERNAL CONTROL DEVICE SETUPCommunication Parameters• Baud rate : 9600 bps (UART)• Data length : 8 bits• Parity : None• Stop bit : 1

6ENGENGLISH6EXTERNAL CONTROL DEVICE SETUPTransmission / Receiving ProtocolTransmission[Command1][Command2][ ][Set ID][ ][Data][Cr][Command 1] : Firs

7ENGENGLISH7EXTERNAL CONTROL DEVICE SETUP* Commands may work differently depending on model and signal.01. Power (Command: k a) ► To control Power *On

8ENGENGLISH8EXTERNAL CONTROL DEVICE SETUPData Min : 00 to Max : 64Ack [i][ ][Set ID][ ][OK/NG][Data][x]09. Tint (Command: k j) ► To adjust the screen

9ENGENGLISH9EXTERNAL CONTROL DEVICE SETUP1 0 05th Band1 0 1 0 120(decimal)Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]* It depends on model, and

10ENGENGLISH10EXTERNAL CONTROL DEVICE SETUPNumber - 22 : Antenna TV (DTV) – Don’t Use Physical Channel Number - 26 : Cable TV (CADTV) - Don’t Use

11ENGENGLISH11EXTERNAL CONTROL DEVICE SETUP24. Input select (Command: x b) (Main Picture Input) ► To select input source for main picture.Transmission

HDMI INLANUSB INAUDIO OUT/H/P OUTANTENNA /CABLE INSatellite INOPTICAL DIGITAL AUDIO OUTPCMCIA CARD SLOTHDMI IN/ARCCOMPONENT INAV INVIDEOVIDEO L/MONO A

12ENGENGLISH12EXTERNAL CONTROL DEVICE SETUP27. Auto Configure (Command: j u) (Depending on model) ► To adjust picture position and minimize image sha

HDMI INLANUSB INAUDIO OUT/H/P OUTANTENNA /CABLE INSatellite INOPTICAL DIGITAL AUDIO OUTPCMCIA CARD SLOTHDMI IN/ARCCOMPONENT INAV INVIDEOVIDEO L/MONO A

HDMI INLANUSB INAUDIO OUT/H/P OUTANTENNA /CABLE INSatellite INOPTICAL DIGITAL AUDIO OUTPCMCIA CARD SLOTHDMI IN/ARCCOMPONENT INAV INVIDEOVIDEO L/MONO A

1243

A B C D E F F G OLED55B6V-TOLED55B6T-TOLED55B6Y-T1229 759 225 715 48.6 19.5 16.2OLED65B6V-TOLED65B6T-TOLED65B6Y-T1451 882 225 838 48.6 25.9 22.6Pow

Please read this manual carefully before operating your set and retain it for future reference.www.lg.comSafety and ReferenceP/NO : MFL69361135 (1606-