LG WM1811CW Uživatelský manuál

100WASHING MACHINESERVICE MANUAL READ THIS MANUAL CAREFULLY TO DIAGNOSE PROBLEMS CORRECTLY BEFORE SERVICING THE UNIT.MODEL : WM2411HW / WM2011 HS

105. OPERATION• Use this button to turn the power On / Off.• Rotate the Cycle selectorknob to select the cycledesigned for differenttypes of fabric an

11• Use this option to preventunwanted use of the washer.Press and hold Quick Cycle andDelay Wash button for 3 secondsto lock / unlock control.• When

12WM2411HWWM2011HS / WM2011HWWM1811CWWM2432HW WM2032HS / WM2032HWWM1832CW

136. WIRING DIAGRAM / PROGRAM CHARTWM2411HW / WM2011HS / WM2011HW / WM2432HW / WM2032HS / WM2032HWWM1811CW / WM1832CW

14

157. TROUBLESHOOTING7-1. BEFORE PERFORMING SERVICEBe careful of electric shock when disconnecting parts for while troubleshooting.The voltage of each

167-4. ERROR DISPLAYIf you press the START/PAUSE button when an error is displayed, any error except willdisappear and the machine will go into the p

17ERROR SYMPTOM CAUSEOVERCURRENTERROR• MAIN PWB ASSEMBLY is out of order.• Winding in the STATOR ASSEMBLY is short-circuited.• The connector (3-pin, m

188-1.DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERATION8. ERROR DIAGNOSIS AND CHECK LISTSYMPTOM GUIDE FOR SERVICE CALLNo power Water inlet troubleIs the p

19SYMPTOM GUIDE FOR SERVICE CALLDoor errorDrain troubleWas the load too large?Visit to service.Visit to service.

CONTENTS1. SPECIFICATIONS ...32.

20SYMPTOM GUIDE FOR SERVICE CALLSuds overflow from theappliance.(In this condition, wash and spin do not operate normally)

Is the supplied voltage 120V AC?Is the voltage between the 2 FILTER ASSEMBLYconnectors 120V AC?Is the LED(1) on?Are the connectors(2) on the PWB loose

NOYESNONOYESNOYESYESNONOYESYESYESNONONOYES22Is water supply shut-off?Is the tap opened?When you press both SPIN SPEED button andSOIL LEVEL button simu

23ABNORMAL SOUNDSOFTENER / BLEACH DOES NOT FLOW INSecure the bolt.Replace the STATORASSEMBLY or ROTORASSEMBLY.Refer toNO WATER SUPPLYCheck the wiring

24Replace theSENSOR SWITCHASSEMBLY.Replace the MAIN PWBASSEMBLY.Repair the DRAIN HOSE ASSEMBLY.Remove foreign material.Reconnect or repair theconnecto

25Push the THERMISTORtightly to the rubber.When checking the THERMISTOR on the tub, is the THERMISTOR loose?HEATING CONTINUOUSLY ABOVE THE SETTING WAT

WILL NOT CIRCULATE WATERIs the impeller of the drain pump clogged?Are the Hose Connector and/or Hose clogged?Is the connector disconnected, disassembl

27SPIN TROUBLECheck the SENSOR SWITCHASSEMBLY or HOSE (Pressure). If the problem is on the SENSORSWITCH ASSEMBLY or theHOSE, replace the SENSORSWITCH

281. Unscrew 7 screws on the Rear Frame.2. Disassemble the Rear Frame.3. Pull the Control panel forward.4. Disconnect connectors.5. Unscrew 5 screws.6

291. Disassemble the 5 hose clamps.2. Release the 5 hoses.3. Unscrew the nut at the lowerpart of the dispenser.4. Unscrew the 4 screws on the holder.5

31. SPECIFICATIONSITEMWM2411HW WM2011HS / WM2011HW WM1811CWWM2432HW WM2032HS / WM2032HW WM1832CWPOWER SUPPLY 120V ~ 60HzPRODUCT WEIGHT 190 lbs. (86 kg

301. Unscrew the 2 screws from upper side of thecabinet cover.2. Unscrew the screw from filter cover.3. Put a flat (–) screwdriver into the both sides

31Clamp Assembly5. Open the door.6. Disassemble the clamp assembly using a flat (–) screwdriver.7. Separate the clamp assembly from cabinetcover.8. Ti

321. Open the door.2. Unscrew the 7 screws from the hinge cover.3. Put a flat (–) screwdriver into the opening of thehinge, and pull out the hinge cov

331. Disassemble the cabinet cover.2. Separate the pump hose, the bellows and the circulation hose assembly from thepump assembly.3. Disassemble the p

341. Disassemble the cabinet cover.2. Separate the heater from the tub.3. Remove any foreign objects (wire, coin, etc.) byinserting a long bar in the

351. Disassemble the back cover.2. Loosen the bolt.3. Pull out the Rotor.4. Unscrew the 2 screws from the tub bracket.5. Loosen the 6 bolts on the sta

3610-1. CABINET & CONTROL PANEL ASSEMBLY10. EXPLODED VIEWA160A125A105F215A495A490A303

37K344 K345K123K115K111K340F315F463K125K343K121K101K122F141 K105F463F46410-2. DRUM & TUB ASSEMBLY

38F300F160F170F120A275HOT (BLUE)A276COLD (RED)F430F435F431F440F436F432F302F30110-3. DISPENSER ASSEMBLY

REPLACEMENT PARTS LISTCAUTION : Before replacing any part of these componentsRead carefully the safety precautions in this manual NOTE : S(Safety

42. FEATURES & TECHNICAL EXPLANATION2-1.FEATURESDirect Drive SystemThe advanced Brushless DC motor directly drives the drum without belt and pull

LG MODEL: WD-10210BD ABWEEUS Run_Date : 2003-04-03YOUR MODEL: WD-2032HW SPECIFICATION: 120V 60HzS AL LOC DESCRIPTION PARTS No. Q'TY REMARKSK121 B

REPLACEMENT PARTS LISTCAUTION : Before replacing any part of these componentsRead carefully the safety precautions in this manual NOTE : S(Safety

LG MODEL: WD-10215BD ATTEEUS Run_Date : 2003-04-03YOUR MODEL: WD-2032HS SPECIFICATION: 120V 60HzS AL LOC DESCRIPTION PARTS No. Q'TY REMARKSK121 B

REPLACEMENT PARTS LISTCAUTION : Before replacing any part of these componentsRead carefully the safety precautions in this manual NOTE : S(Safety

LG MODEL: WD-12210BD ABWEEUS Run_Date : 2003-04-03YOUR MODEL: WD-2432HW SPECIFICATION: 120V 60HzS AL LOC DESCRIPTION PARTS No. Q'TY REMARKSK115 S

REPLACEMENT PARTS LISTCAUTION : Before replacing any part of these componentsRead carefully the safety precautions in this manual NOTE : S(Safety

LG MODEL: WD-90210BD ABWEEUS Run_Date : 2003-04-03YOUR MODEL: WD-1832CW SPECIFICATION: 120V 60HzS AL LOC DESCRIPTION PARTS No. Q'TY REMARKSK121 B

101DEC. 2002 PRINTED IN KOREAP/No.:3828ER3013T

52-2.FUZZY LOGIC WASHING TIME OPTIMIZATIONTo get the best washing performance, optimal time is determined by the water temperature, the selected washi

63. PARTS IDENTIFICATIONACCESSORIES• If the supply cord isdamaged, it must bereplaced by themanufacturer or itsauthorized servicetechnician in order t

7Before servicing, ask the customer what the trouble is.Check the setup (power supply is 120V AC, remove the transit bolts...).Check with the trouble

8HOW TO CONNECT THE INLET HOSEVerify that the rubber washer is inside of thevalve connector.Connect the inlet hose firmly to prevent leaks.CONNECT THE

9TEST OPERATIONConnect the power plug tothe outlet.Connect the inlet hose. Press the POWER button twiceto restart.Press the SPIN SPEED button.Press th